Industrial flooring for parking lots

Parking lot floors must withstand constant mechanical loads, moisture, reagents and temperature fluctuations. Wear-resistant coatings prevent dusting, cracking and ensure safe movement of vehicles

We offer a full range of services for the installation and restoration of industrial floors for parking lots, from preparing and repairing the concrete base to finishing the surface. Depending on the facility's requirements, we offer several practical solutions: polished concrete, which is many times stronger than poured alternatives, does not dust, and does not absorb moisture, as well as an anti-slip "coat" coating with a textured relief surface for improved grip. This coating is particularly relevant for exits, ramps, and high-traffic areas.

Coating comparison

Use Shift + Scroll to scroll the table horizontally

Properties of coatings	High-strength polished and polished concrete	Topping - dry hardener	Terrazzo decorative flooring	Ceramic tiles	High-performance polymer floors
Hardness	Very hard (7 on the Mohs scale)	Very hard (>6 on the Mohs scale)	Very hard (>8 on the Mohs scale)	Very hard (>6 on the Mohs scale)	Average hardness (<4 on the Mohs scale)
Impact strength	Highest abrasion resistance, not scratch resistant	High abrasion resistance	Highest abrasion resistance, not scratch resistant	High abrasion resistance	Easily scratched
Heat resistance (including frost resistance)	High	High	High	Medium	Low
Resistance to chemical reagents	High resistance to most chemicals, low resistance to acids	High resistance to most chemicals, low resistance to acids	High resistance to most chemicals, low resistance to acids	Resistance is determined by the type of grout between seams	High resistance to most chemicals, low resistance to solvents color loss
Thermocycling (in cycles)	200-400	150	600-800	200	0-100
Impact strength	Highest impact resistance	High impact strength, possible delamination of the hardened layer	Highest impact resistance	Low impact strength, high brittleness	High impact resistance, risk of coating delamination
vapor permeability	Yes	Yes	Yes	Yes	No
Water resistance	Yes	Yes	Yes	Yes	Yes
Sensitivity to capillary moisture	Not sensitive	Sensitive, shoots	Not sensitive	Sensitive	Sensitive, possible peeling, possible swelling, blistering
Can be used outdoors and in cold rooms	Recommended	Not recommended (not living at all)	Recommended	Perhaps	Not recommended
Stain resistance	Good resistance	Low resistance	Good resistance	High resistance	High resistance
Dusting	Dustless floors	May dust after abrasion of the membrane forming layer, destruction of the top layer	Dustless floors	Interstitial grout may be dusty	Dustless floors
Curing time before operation	The final coating takes about 7 days to gain strength	8-28 days (the warmer the better)	The final coating takes about 7 days to gain strength	7 days after laying	The final coating takes about 3 days to gain strength
Maintaining the original appearance	Ages 5-7	1 year	5-10 years		1 year
Durability	More than 15 years	10 years	More than 15 years	Requires repairs every 3-5 years	Lacquer renewal every 2 years
Maintenance	Easy cleaning, low maintenance costs	Renew once a year with kuring (varnish), high maintenance costs, cracking possible (depending on the substrate)	Easy cleaning, low maintenance costs	Regular repairs, high maintenance costs	Easy to clean, cannot be repaired locally, requires replacement of the entire top layer, high repair costs, cheap to maintain
Quick installation option	Yes	Yes	No (Concrete quality problems and fraction)	Yes	Yes
Quick repair capability	Yes	Yes	Yes	Full replacement (repair fails)	No
Type of surface (glossy, matte, customizable)	Customizable	Customizable	Customizable	Customizable	Customizable
Sterility	Yes	No	Yes	Yes	Yes (no seams)
Seamlessness	No	No	Customizable	No	Yes
hypoallergenicity	Yes	No	Yes	No	Yes
Fire safety	KM0	KM1	KM0	KM0	KM1-KM2
Environmental friendliness	Yes	No	Yes	Yes	Yes
Static control, intrinsic protection	Yes	Yes	Yes	Yes	No
UV resistance	Yes	Yes	Yes	Yes	Depending on the decision
Light reflectance coefficient	A good one	Bad	A good one	Bad	Bad
Odor, emission of volatile compounds	No	No	No	No	No

Additional services

Use Shift + Scroll to scroll the table horizontally

	High-strength polished and polished concrete	Topping - dry hardener	Terrazzo decorative flooring	Ceramic tiles	High-performance polymer floors
Heat resistance	Yes	No	Yes	No	Yes
Thermocycling	Yes	No	Yes	no	Yes
Can be used outdoors and in cold rooms	Yes	No	Yes	No	Yes
Quick installation option	Yes	Yes	No	Yes	Yes
Quick repair capability	Yes	No	No	Yes	No
Sterility	No, present by default	No	No, present by default	No	No
Seamlessness	No	No	Yeah, if the stomping grounds (topknot is our version of Terrazzo)	No	Yes
hypoallergenicity	Yes	No	Yes	Yes	Yes
Slipperiness	Yes	Yes	Yes	Yes	Yes
Environmental friendliness	Yes	No	Yes	No	Yes
Static control, intrinsic protection (For data centers and electronics manufacturing)	Perhaps	No	No	No	Yes
Decorating possibilities (Color, texture, filling)	Yes A colorant, but not a brightener	No	Yes Fraction, color, pattern	Yes	Yes
Ability to provide resistance to oxidizing agents, organic acids and chemical reagents	Yes	No	Yes	Yes	Yes
Possibility to ensure GOST flatness	Yes	No	Yes	No	No

Features of industrial flooring for parking lots

Parking lot floors should provide maximum durability and resistance to aggressive operating conditions:

high wear resistance and resistance to mechanical loads from transportation
protection against moisture, reagents, oils and road chemicals
resistance to temperature fluctuations and ultraviolet light (for street parking)
anti-slip surface, fire safety and anti-static properties
cracking resistance, minimal dusting effect
Aesthetic appearance and easy maintenance

Polymer, poured and concrete floors for parking lots are actively used in underground and surface parking lots, shopping centers and residential complexes. We offer both the installation of new coatings, including epoxy and polyurethane systems, and repair of parking lot floors, taking into account the technical condition and operational tasks.

Our projects

All projects

Parking lot of Odinburg Residential Complex

Input data for the CP

We will need the following information to prepare a quote for the installation or repair of parking lot flooring:

Photos and videos of the area of the work being done;
Information on the current floor covering in the work area and the need to remove it;
Approximate area of work;
Facility Address.

This data will help us provide you with the most accurate and efficient estimate of the cost and timing of the work.